You're viewing a previously published revision of this guide.  View latest revision

Older
May 31, 2016 - 11:05:13
Mar 06, 2025 - 11:03:50 Mar 06, 2025 - 11:03:54 Mar 06, 2025 - 11:03:44 Mar 06, 2025 - 11:03:51 Jun 07, 2016 - 08:06:10 Jun 07, 2016 - 08:06:07 Jun 03, 2016 - 11:06:21 May 31, 2016 - 05:05:32 May 31, 2016 - 05:05:35 May 31, 2016 - 05:05:46 May 31, 2016 - 05:05:18 May 31, 2016 - 05:05:03 May 31, 2016 - 05:05:27 May 31, 2016 - 11:05:41 May 31, 2016 - 11:05:13 May 31, 2016 - 11:05:53 May 30, 2016 - 08:05:30 May 30, 2016 - 08:05:38 May 30, 2016 - 08:05:16 May 30, 2016 - 08:05:31 May 30, 2016 - 08:05:50 May 30, 2016 - 08:05:19 May 30, 2016 - 08:05:41 May 04, 2016 - 01:05:50 May 04, 2016 - 01:05:06 May 04, 2016 - 01:05:12 May 04, 2016 - 01:05:17 May 04, 2016 - 01:05:58 May 04, 2016 - 01:05:47 Mar 30, 2016 - 09:03:54 Mar 30, 2016 - 09:03:34 Mar 30, 2016 - 09:03:00 Mar 30, 2016 - 09:03:43 Mar 30, 2016 - 09:03:28 Mar 30, 2016 - 09:03:08 Mar 30, 2016 - 09:03:49
Newer

Mirror Mount Sub Assembly

Written By: SeeMeCNC (and one other contributor)
  • Comments: 0
  • Favorites: 0

Difficulty

Very easy

Steps

4

Time Required

Suggest a time??

Sections

1

Flags

3

In Progress

In Progress

This guide is currently being written. Reload periodically to see the latest changes.

User-Contributed Guide

User-Contributed Guide

This guide is not managed by the site's staff.

Private

Private

This guide will not appear in search results and can only be viewed by team members!

Quiz

0

Introduction

This Assembly Guide will walk you through building the Mirror Mount Sub-Assembly which is used on the DropLit V2.

    • Attach the Mirror Mount Side to the Mirror Mount as shown in the video, pay particular attention to the part orientation.

    • There should be one spacer installed in between the Mirror Mount Side and the Mirror Mount.

    • The fasteners should be not be fully tightened. After the Mirror Mount is fully assembled you can tighten these screws up to the point that they are tight, but still allow the mirror to pivot.

    • Attach the Mirror Mount Side to the Mirror Mount as shown in the video, pay particular attention to the part orientation.

    • There should be one spacer installed in between the Mirror Mount Side and the Mirror Mount.

    • The fasteners should be not be fully tightened. After the Mirror Mount is fully assembled you can tighten these screws up to the point that they are tight, but still allow the mirror to pivot.

    • Attach the previously assembled Mirror Mount (Left) and (Right) Sides to the Cross Brace and Center Brace as shown in the animation.

    • You can tighten these screws fully.

    • Use the remaining 6-32 x 1" Phillips Pan Head screw to attach the base.

    • You can fully tighten this screw.

Author

with 1 other contributor

SeeMeCNC

Member since: 9/11/15

13,012 Reputation

33 Guides authored

View Statistics:

Past 24 Hours: 0

Past 7 Days: 1

Past 30 Days: 1

All Time: 451