You're viewing a previously published revision of this guide.  View latest revision

Older
Jun 13, 2016 - 12:06:28
Mar 06, 2025 - 11:03:34 Mar 06, 2025 - 11:03:54 Mar 06, 2025 - 11:03:01 Mar 06, 2025 - 11:03:15 Jun 14, 2016 - 11:06:19 Jun 14, 2016 - 10:06:23 Jun 14, 2016 - 10:06:19 Jun 14, 2016 - 10:06:19 Jun 14, 2016 - 10:06:13 Jun 14, 2016 - 10:06:47 Jun 14, 2016 - 10:06:06 Jun 14, 2016 - 10:06:42 Jun 14, 2016 - 10:06:59 Jun 14, 2016 - 10:06:12 Jun 14, 2016 - 10:06:35 Jun 14, 2016 - 10:06:37 Jun 14, 2016 - 10:06:07 Jun 14, 2016 - 10:06:41 Jun 14, 2016 - 10:06:59 Jun 13, 2016 - 01:06:28 Jun 13, 2016 - 01:06:59 Jun 13, 2016 - 01:06:07 Jun 13, 2016 - 01:06:45 Jun 13, 2016 - 01:06:47 Jun 13, 2016 - 01:06:18 Jun 13, 2016 - 01:06:16 Jun 13, 2016 - 12:06:37 Jun 13, 2016 - 12:06:04 Jun 13, 2016 - 12:06:25 Jun 13, 2016 - 12:06:05 Jun 13, 2016 - 12:06:28 Jun 13, 2016 - 12:06:04 Jun 13, 2016 - 12:06:18 Jun 13, 2016 - 12:06:50 Jun 13, 2016 - 12:06:12 Jun 13, 2016 - 12:06:41 Jun 13, 2016 - 12:06:27 Jun 07, 2016 - 08:06:39 Jun 03, 2016 - 11:06:38 May 31, 2016 - 11:05:24 May 31, 2016 - 11:05:37 May 31, 2016 - 11:05:11 May 31, 2016 - 11:05:51 May 31, 2016 - 11:05:05 May 31, 2016 - 11:05:23 May 31, 2016 - 10:05:09 May 31, 2016 - 10:05:13
Newer

Droplit v2 Installing Firmware / Software

Written By: SeeMeCNC (and one other contributor)
  • Comments: 0
  • Favorites: 0

Difficulty

Moderate

Steps

5

Time Required

Suggest a time??

Sections

1

Flags

3

In Progress

In Progress

This guide is currently being written. Reload periodically to see the latest changes.

User-Contributed Guide

User-Contributed Guide

This guide is not managed by the site's staff.

Private

Private

This guide will not appear in search results and can only be viewed by team members!

Quiz

0

  1. You can Download the firmware here: https://github.com/seemecnc/Firmware Extract the files from the zipped folder. If you are new to extracting files, you will need to go to the folder where the firmware was downloaded to (most commonly your downloads folder)

    • You can Download the firmware here: https://github.com/seemecnc/Firmware

    • Extract the files from the zipped folder.

    • If you are new to extracting files, you will need to go to the folder where the firmware was downloaded to (most commonly your downloads folder)

    • Right Click on the folder named: Firmware Master, and from the options available choose EXTRACT ALL.

    • Choose Extract in the dialogue box that pops up.

    • You can now copy and past the extracted folder of firmware files to your preferred location ie. Desktop, My Documents etc.

    • In order to compile and upload the firmware to the RAMBo controller, you're going to need the Arduino IDE. This is an open source software development environment targeted at the Arduino family of ATMega-based micro-controller project boards. At its heart, the RAMBo controller is just an Arduino Mega 2560 with a lot of goodies attached to it.

    • You can download the Windows, MacOS and Linux version of the Arduino IDE from here: https://www.arduino.cc/en/Main/OldSoftwa... Choose the appropriate Platform. As of the time of this writing, we are using Arduino 1.6.4 There are many versions available of Arduino, but all are compatible.

    • Put microSD card into Raspberry Pi and turn the power to the Droplit v2 on

    • Connect an ethernet cable to the Raspberry Pi and your Router (this is a one time setup requirement until the wifi has been connected)

    • To find out your Raspberry Pi's IP address open your computer's network area. Or visit the online dashboard http://www.nanodlp.com/dashboard to see online nanoDLP printers in your network

Author

with 1 other contributor

SeeMeCNC

Member since: 9/11/15

13,012 Reputation

33 Guides authored

View Statistics:

Past 24 Hours: 0

Past 7 Days: 0

Past 30 Days: 2

All Time: 597